電子萬能試驗機 電子拉力試驗機 沖擊試驗機 熔體流動速率測定儀 塑料滑動摩擦試驗儀 萬能制樣機 高阻測定儀 紙箱耐壓試驗機 安全帽沖擊試驗機 電壓擊穿試驗儀 馬丁耐熱試驗儀 塑料球壓痕硬度計
撥號13581986832

聯系我們

  • 北京冠測精電儀器設備有限公司
  • 公司地址:北京市昌平區沙河王莊工業園內
  • 公司傳真:010-51651740
  • 聯系QQ:1225767627

掃一掃,立刻溝通

你的位置:首頁 > 產品展示 > 力學性能檢測設備 > 電子拉力機 >進口法國泰康壓縮機制冷塑料低溫脆化試驗機

產品詳細頁
進口法國泰康壓縮機制冷塑料低溫脆化試驗機

進口法國泰康壓縮機制冷塑料低溫脆化試驗機

  • 產品型號:CJD-III型
  • 更新時間:2017-06-06
  • 產品介紹:CJD-III型
    (進口法國泰康壓縮機制冷塑料低溫脆化試驗機)
    一、滿足標準:
    GBT 5470-2008 塑料 沖擊法脆化溫度的測定
  • 在線留言 010-57223838

產品介紹

中英文對照資料

 

 (imported French Taikang compressor refrigeration plastic low temperature brittleness)

(進口法國泰康壓縮機制冷塑料低溫脆化試驗機)

===================================

一、滿足標準:

 

One, meet the standards:

 

GBT 5470-2008 塑料 沖擊法脆化溫度的測定

 

Determination of GBT 5470-2008 plastic impact embrittlement temperature

==================================

二、產品概述

 

Two, product overview

 

塑料低溫脆性試驗機是測定塑料在規定條件下試樣受沖擊出現破壞時的zui高溫度,即為脆性溫度,可以對非硬質塑料及其他彈性材料在低溫條件下的使用性能作比較性鑒定。溫度和低溫性能的優劣。因此無論在科學研究材料及生產過程的控制等方面均是不可缺少的。

 

Low temperature brittle plastic testing machine is the determination of plastics under specified conditions of sample temperature impact appeared at failure, namely the brittle temperature, can be compared to identify the properties of non rigid plastics and other elastic material at low temperature. Temperature and low temperature performance. Therefore, both in terms of scientific research materials and production process control are necessary.

 

本儀器是根據GB/T5470國家標準設計的,研制開發的壓縮機制冷設備。本設備采用復疊式壓縮機制冷技術,利用熱平衡原理及循環攪拌方式,達到對試樣的自動均勻冷卻、恒溫。

 

The instrument is designed according to the national standard GB/T5470, the compressor refrigeration equipment newest development. The equipment adopts cascade refrigeration compressor refrigeration technology, based on the heat balance principle and circulating stirring mode, to achieve automatic uniform cooling, temperature of specimen.

========================================

Three, low temperature brittle plastic testing machine technical parameters

 

1、控溫范圍: -70

 

1, the range of temperature control: -70

 

2、降溫速度: 2小時左右達到-70

 

2, the cooling rate: about 2 hours to reach -70

 

(注:使用環境在室溫下使用,工作時保持壓縮機散溫效果,可將側門全部打開)

 

(Note: the use of environment, at room temperature maintained compressor heat effect, work can be a side door open all)

 

3、恒溫后,試驗3min時間內溫度波動:<±1

 

3, constant temperature, temperature fluctuation test 3min time: < ± 1

 

4、zui大外形尺寸:900×505×800mm(長×高×寬)

 

4, the maximum dimensions: 900 x 505 x 800mm (width)

 

5、工作室外形尺寸:200×140×100mm(長×高×寬)

 

5, studio size: 200 * 140 * 100mm (length x Height x width)

 

6、冷卻介質:乙醇或其他不凍液

 

6, the cooling medium: ethanol or other non freezing solution

 

7、攪拌電機:15W

 

7, a stirring motor: 15W

 

8、工作電源220V~240V,50Hz,2KW

 

8, a working power supply 220V~240V, 50Hz, 2KW

==============================================

四、塑料低溫脆性試驗機結構原理

 

Four, low temperature brittle plastic testing machine structure principle

 

1、本設備由制冷壓縮機主機體、加熱裝置、電子控制箱、冷卻槽、冷卻介質循環系統、自動報警裝置等部分組成。啟動制冷開關后,壓縮機開始工作,制冷系統進入正式工作狀態。制冷壓縮機連續不斷的工作,當接近設定溫度時,冷卻槽中的加熱裝置開始按比例提供熱量,用以平衡制冷系統產生的多余冷量,以達到恒溫的目的。攪拌可使冷卻槽內的冷卻介質不斷循環,使溫度均勻*。

 

1, the equipment is composed of a refrigerating compressor main body, a heating device, an electronic control box, cooling tank, a cooling medium circulating system, automatic alarm device components. Start the cooling after the switch, the compressor starts to work, the refrigeration system into the official working state. The work of refrigeration compressor continuously, when close to the set temperature, the heating device cooling tank to provide heat is proportional to balance, with excess cold refrigeration system, in order to achieve the purpose of constant temperature. Agitation can make the cooling medium cooling groove continuous cycle, so that the temperature is uniform.

 

2、試樣夾持器

 

2, the sample holder

 

A試樣每次可夾持15

 

The A sample each holding 15

 

3、沖擊裝置

 

3, the impact device

 

沖擊裝置由沖擊錘和自鎖機構組成。

 

Impact device consists of a hammer and a self-locking mechanism.

 

4、沖擊器

 

4, the impactor

 

4.1 A試樣:

 

4.1 A samples:

 

a)沖頭半徑為1.6±0.1mm;

 

A) punch radius is 1.6 ± 0.1mm;

b)鉗口半徑為4.0±0.1mm;

 

B) jaw radius is 4 ± 0.1mm;

c) 沖頭中心線與夾具間隙為3.6±0.1mm;

 

C) punch center line and fixture clearance is 3.6 ± 0.1mm;

d)沖頭的外側與夾具間隙為2.0±0.1mm

 

D) side clearance and fixture punch is 2 ± 0.1mm

 

4.2 B試樣:

 

4.2 B samples:

 

a)沖頭半徑為1.6±0.1mm;

 

A) punch radius is 1.6 ± 0.1mm;

b)沖頭中心線與夾具間隙為7.87±0.25mm;

 

B) punch center line and fixture clearance is 7.87 ± 0.25mm;

c) 沖頭的外側與夾具間隙為6.35±0.25mm

 

C) side clearance and fixture punch is 6.35 ± 0.25mm

=====================================================

Use method five, low temperature brittle plastic testing machine

 

5.1向冷井中注入冷凍介質(一般為工業乙醇),其注入量應保證夾持器的下端到液面的距離為75±10mm。

 

5.1 to the cold well into the freezing medium (for general industrial ethanol), the injection volume should ensure that the holder is to the surface distance of 75 ± 10mm.

5.2接通電源,溫控儀和計時器顯示燈亮。

 

5.2 connect the power supply, a temperature controller and timer display lights.

 

5.3將試樣垂直夾在夾持器上。夾的不宜過緊或過松,以防止試樣變形或脫落。

 

5.3 samples of vertical clip on the holder. Clip shoulds not be too tight or too loose, to prevent deformation or fall off.

 

5.4按下夾持器,開始冷凍試樣,同時啟動時序控制開關(或按動秒表)計時。試樣冷凍時間規定為3.0±0.5min。試樣冷凍期間,冷凍介質溫度波動不得超過±1℃。

 

5.4 press the holder, began to freeze samples, at the same time start timing control switch (or press stopwatch timing). Set sample freezing time was 3 ± 0.5min. Sample freezing, freezing medium temperature shall not exceed ± 1 .

5.5拉動沖擊錘自鎖手柄,沖擊錘在重力作用下自由下落,對試樣做沖擊動作。

 

5.5 driving hammer self-locking handle, the hammer free falls under the action of gravity, do the impact action of specimen.

 

5.6取下試樣,將試樣按沖擊方向彎曲成180°,仔細觀察有無破壞。

 

5.6 remove the specimen, the specimen is bent into a 180 degree according to the impact direction, carefully observe whether failure.

 

5.7試樣經沖擊后(每個試樣只準沖擊一次),如出現破壞時,應提高冷凍介質的溫度,否則降低其溫度,繼續進行試驗。通過反復試驗,確定至少有兩個試樣不破壞的zui低溫度和至少一個試樣破壞的zui高溫度,如這兩個結果相差不大于1℃時,即試驗結束。

 

5.7 samples (each sample by shock after shock, only once) such as damage, should improve the freezing medium temperature, or reduce the temperature, continue to test. Through repeated tests, identified at least the minimum temperature of two samples is not destroyed and at least one sample destruction of the highest temperature, such as the two results is not more than 1 , that is the end of the experiment.

=======================================

六、塑料低溫脆性試驗機試驗標準

 

Test standard of six, low temperature brittle plastic testing machine

 

6.1規格

 

6.1 specifications

 

A:試樣的長為20.0±0.25mm,寬為2.5±0.1mm,厚為2.0±0.1mm的條形試樣

 

A: sample length of 20 ± 0.25mm, 2.5 ± 0.1mm width, thickness is 2 ± 0.1mm bar specimens

 

B:試樣的長為31.75±6.35mm,寬為6.35±0.51mm,厚為1.91±0.13mm

 

B: sample length of 31.75 ± 6.35mm, 6.35 ± 0.51mm width, thickness is 1.91 ± 0.13MM

 

6.2要求

 

6.2 requirements

 

試樣的表面應光滑,無外來雜質及損傷。成品應經打磨后裁制成相應尺寸。

 

The surface should be smooth, no foreign impurities and injury. The finished products should be polished after the cut into the appropriate size.

 

留言框

  • 產品:

  • 您的單位:

  • 您的姓名:

  • 聯系電話:

  • 常用郵箱:

  • 省份:

  • 詳細地址:

  • 補充說明:

  • 驗證碼:

    請輸入計算結果(填寫阿拉伯數字),如:三加四=7
??
在線咨詢
QQ客服
QQ:1225767627
電話咨詢
010-57223838

關注微信
又爽又色又高潮的免费视频_东北50岁熟妇露脸在线_av色图_噗呲噗呲捣出白沫蜜汁